Arcone Clean Air Flow User Manual

Installation:1. Line up the edges as shown (fi g. 2). 2. Slide the battery into the Blower.3. Make sure there is an audible click as the battery is sec

Filter Installation:1. Remove any Filter packaging from the Filter.2. Remove the Filter Cap from the Blower (fi g. 3). 3. Remove the old fi lter (if ins

#12.3 Blower1. Install the Breathing Tube into the Blower as shown (fi g. 6). 2. Operate the Blower (fi g. 7). #2fairAudible Alarm (short beep) &

2.4 Headtop1. Install and Lock the Breathing Tube into the Airduct on the Headtop (fi g. 8) 2. (Welding Helmet headtops only) Adjust the headgear front

Hard Hat headtops only:1. Install accessory slot plug (straight bill hard hat only), if not already installed or optional accessory. (fi g. 9) 2. Remov

2.6 Pre-Operational InspectionCheck the following before donning your Clean Air FlowTM PAPR system. If any of the following are not in compliance refe

Failure to properly connect the Breathing Tube to the Helmet Assembly and to confi rm airfl ow through the system to the Breathing Zone could lead to co

2.8 TroubleshootingIf, at any time during operation, you detect an odor or taste of gas or vapor, or if you feel eye or throat irritation, you must

3.0 Maintenance and Storage3.2 Cleaning1. ALWAYS INSPECT YOUR CLEAN AIR FLOWTM PAPR system after cleaning. Clean the external surfaces of the Clean Ai

Cleaning Continued...2. Detach the breathing tube from the blower unit and the helmet assembly (see section 4.3 & 4.4), and wipe the connection si

CAUTIONWARNINGDefi nition of Safety Signal Words per ANSI Z 535.4Indicates a potentially hazardous situation which, if not avoided, could result in dea

3.4 Storage• Before storing the Clean Air FlowTM system, it should be thoroughly dry. Do Not Keep used fi lter in the same enclosed storage space a

The Blower and Battery Units are supplied as seal-testedunits. Any attempt to open or repair the unit will result inthe termination of the limited w

Faceseal Replacement: Viper continued...Installation: 1. Line up the bottom seam of the Faceseal to the centerline of the Helmet (fi g. 16)2. Attach th

5. Thread the Airduct over the Headgear and attach to the front and top of the Headgear with the Velcro strips as shown (fi g. 19). VelcroVisor Rep

4. Pull the Faceseal off the Hard Hat.Installation: (Procedure is same for reverse bill hard hat assembly with exception of faceseal visor orienated o

Faceseal Replacement: Vision AirDuct Headgear Assemblyp Welding Helmet ShellFace Seal of Corresponding Headtop (CA-COL-XX) Airduct Headgear Assembly

4.6 Waist BeltRemoval:1. Remove the Waist Belt from the clip.2. Unthread the Waist Belt Strap from the Blower.Installation: 1. Thread the Waist Belt S

4.7 Airduct Headgear Assembly Replacement Welding Helmet ShellAirduct Headgear Assembly (CA-HGA-01) Face Seal (CA-COL-XX)Knob Pivot StopBoltStep

4.8 Auto-Darkening Lens ReplacementRefer to ArcOne’s Auto-Darkening Welding Helmets- “User Instruction Manual” which is enclosed for information on th

5.1.3 Helmet Assembly: Part No. Description CA-HGA-01 Ratchet Headgear - AirDuct Assembly 01-HGA Ratchet Headgear Fastener Assembly

Table Of Contents1.0 General Information1.1 Introduction1.2 Operating Principles1.3 Respirator Approvals & Limitations1.4 Helmet & Weldin

5.2 Technical Specifi cations Compact Air PAPR SystemBlo

Note: NIOSH Approval covers complete respirator systems only, as confi gured from approved components as referenced on the NIOSH approval label for t

ArcOne warrants the complete Clean Air FlowTM PAPR Systems for one (1) year from the date of purchase against all manufacturing defects resulting fr

4.6 Servicing Your Clean Air FlowTM PAPR SystemPlease contact ArcOne directly for any questions regarding the function of your Clean Air FlowTM PAPR

Please Contact: ARCONE Service Center,Telephone: 800-223-4685, Fax: 508-884-9666OrVisit Our Website www.arc1weldsafe.comA Division of A. C. E. Inte

Please Contact: ARCONE Service Center,Telephone: 800-223-4685, Fax: 508-884-9666OrVisit Our Website www.arc1weldsafe.comA Division of A. C. E. Inte

Please Contact: ARCONE Service Center,Telephone: 800-223-4685, Fax: 508-884-9666OrVisit Our Website www.arc1weldsafe.comA Division of A. C. E. Inte

byA complete Clean Air FlowTM System Includes:• A Choice of Lightweight and Durable Nylon Vision or Viper Welding Helmet or a Hard Hat Visor combin

1.0 General Information1.1 IntroductionCongratulations! You have purchased the ultimate in comfortable welding powered respiratory protection equ

This Clean Air FlowTM system is used in a welding environment where protection is required against harmful particles and mist. The Clean Air FlowTM ,

1.3 Respirator Approvals & LimitationsThe Clean Air FlowTM System as described in this instruction manual has been approved by the following agen

Cautions and Limitations (refer to the enclosed Approval Labels)• Not for use in atmospheres containing less that 19.5 percent oxygen.• Not for use in

#11.4 Helmet and Auto-Darkening Lens ApprovalsThe ArcOne helmet, consisting of the Vision and Viper series and the full family of ArcOne’s Auto-Darke